View previous topic :: View next topic |
Author |
Message |
pombok Newbie
Joined: 23 Feb 2023 Posts: 9 Location: Exeter
|
Posted: Mon Feb 27, 2023 22:01 Post subject: Corroded fuel filler pipe, where to get new set (3 pipes) |
|
|
Hi all,
I have a 57 reg Shogun (V80 Mk IV I think) LWB. 3.2 DiD. Got the water in fuel filter light come on a couple of days ago, changed fuel filter and it went off for a while but back on now.
Checked fuel lines under RHS rear wheel arch and heavily corroded, vapor hose completely rusted through and chassis mount full of rust too.
Looking for a replacement but struggling to find the correct one. Mine has the main fuel filler line, the breather line (connects back to fuel filler) and what I assume is a vapour release line. The vapour release line looks to have a filter on the end of it.
Seen loads with 2 vapour lines but mine only has 1. Any idea on part #s or where to source?
Thank you! |
|
Back to top |
|
|
Google Sponsor
|
Posted: Mon Feb 27, 2023 22:01 Post subject: Google Ads keep the POCUK free to join! |
|
|
|
|
Back to top |
|
|
radiomike ******
Joined: 04 Aug 2010 Posts: 1483 Location: North Bucks
|
|
Back to top |
|
|
pombok Newbie
Joined: 23 Feb 2023 Posts: 9 Location: Exeter
|
Posted: Tue Feb 28, 2023 18:13 Post subject: |
|
|
That one, yes. Sadly they don’t deliver to the UK.
Have gone with a 4 pipe version and will hope it fits! |
|
Back to top |
|
|
radiomike ******
Joined: 04 Aug 2010 Posts: 1483 Location: North Bucks
|
Posted: Tue Feb 28, 2023 19:41 Post subject: |
|
|
Strange that it is no longer available, it is known to have a high failure rate. |
|
Back to top |
|
|
pombok Newbie
Joined: 23 Feb 2023 Posts: 9 Location: Exeter
|
Posted: Tue Feb 28, 2023 19:43 Post subject: |
|
|
DO you perhaps know where I could get a part number from? The manual I have (from this parish's links) just gives the names of the parts. |
|
Back to top |
|
|
radiomike ******
Joined: 04 Aug 2010 Posts: 1483 Location: North Bucks
|
Posted: Tue Feb 28, 2023 20:14 Post subject: |
|
|
pombok wrote: |
DO you perhaps know where I could get a part number from? The manual I have (from this parish's links) just gives the names of the parts. |
It is on the link I sent. |
|
Back to top |
|
|
pombok Newbie
Joined: 23 Feb 2023 Posts: 9 Location: Exeter
|
Posted: Wed Apr 26, 2023 13:15 Post subject: |
|
|
Just to come back to this, the 4 pipe and 3 pipe variants all fit perfectly and seem to be interchangeable. I had a 3 pipe version and used a 4 pipe version, fits all ok. Bolt holes all in the same place. |
|
Back to top |
|
|
iam_TJ LifeTime Member
Joined: 10 Apr 2013 Posts: 351 Location: Europe
|
Posted: Thu Apr 27, 2023 18:38 Post subject: |
|
|
It'd be good if you could point us to where you bought the replacement from, cost, etc, because others may well be needing the same thing doing at some point! |
|
Back to top |
|
|
pombok Newbie
Joined: 23 Feb 2023 Posts: 9 Location: Exeter
|
Posted: Fri Apr 28, 2023 12:33 Post subject: |
|
|
This one for the fuel filler neck: https://www.ebay.co.uk/itm/254663806574
This one for the neck pipe: https://www.ebay.co.uk/itm/165076808053
Whilst you're down there you may as well replace the gasket around the nozzle and the bolts which I replaced with stainless steel ones.
This page shows the actual parts and official part #s, but it also gives you some measurements of the parts you will need. (e.g. MS605158 HOSE, EMISSION SOLENOID VALVE 6x2000 : this is 2000mm of a 6mm pipe, MB400550 BOLT, FUEL LINE Washer assembled,6x16 : these are M6 16mm bolts).
Hope that helps someone in the future! |
|
Back to top |
|
|
|