|
The Mitsubishi Pajero Owners Club® The Mitsubishi Pajero, Shogun, Montero, Challenger, Raider and EVO 4x4 Owner's Club
|
View previous topic :: View next topic |
Author |
Message |
The Bunney man **
Age: 68 Zodiac: Joined: 10 May 2013 Posts: 66 Location: Loughborough
|
Posted: Thu May 08, 2014 23:29 Post subject: Electronics ! |
|
|
Is there anyone on here that deal with the ubiquitous Dry solder joint on rev counters, well beyond most of our ability levels I would say, would really love a working rev counter ! |
|
Back to top |
|
|
Google Sponsor
|
Posted: Thu May 08, 2014 23:29 Post subject: Google Ads keep the POCUK free to join! |
|
|
|
|
Back to top |
|
|
Dmcmylor ******
Age: 51 Zodiac: Joined: 01 Oct 2011 Posts: 1827 Location: Glossop, Derbyshire
|
Posted: Fri May 09, 2014 0:49 Post subject: |
|
|
Lots of us just learn to live it not working But I know what you mean, i'd like mine working , it's on the to do list, only right near the bottom |
|
Back to top |
|
|
REVOGEL LifeTime Member
Age: 84 Zodiac: Joined: 23 Dec 2006 Posts: 4276 Location: Cent. Amelias. Reg 10. Guyana South America
|
Posted: Fri May 09, 2014 13:12 Post subject: |
|
|
Soldering is not difficult You just need a reasonably good Iron, a reel of thin fluxed core solder. Practice on some bits of copper wire. Clean till bright apply solder to each piece [tin] hold together NOT with hands apply solder till it flows do not move joint till it sets. When doing printed cct boards. a HOT iron for a short time is the way, else you may lift the copper.
Hope some of you take the time to learn. |
|
Back to top |
|
|
vmaxsnoopy LifeTime Member
Age: 65 Zodiac: Joined: 23 Apr 2004 Posts: 1353 Location: Lincolnshire
|
Posted: Fri May 09, 2014 21:01 Post subject: |
|
|
There is a supplier I use in Sheffield that repairs commercial vehicle dash displays, ECU.s and the like. Last time I was in there I enquired about repairing and testing electronic rev counters. They reckon that it will not be a problem as they have the equipment both to test, calibrate, and rebuild to OE spec with a 12 month warranty. I am going to drop in my spare non-working rev counter next week, for them to look at. Ball park repair cost estimate around £40.00. Will post the result if successful along with contact details, and hopefully negotiate a bit of club discount too. |
|
Back to top |
|
|
The Bunney man **
Age: 68 Zodiac: Joined: 10 May 2013 Posts: 66 Location: Loughborough
|
Posted: Fri May 09, 2014 22:07 Post subject: |
|
|
This sounds promising mate, will watch with interest ! |
|
Back to top |
|
|
The Bunney man **
Age: 68 Zodiac: Joined: 10 May 2013 Posts: 66 Location: Loughborough
|
Posted: Fri May 09, 2014 22:10 Post subject: |
|
|
REVOGEL wrote: |
Soldering is not difficult You just need a reasonably good Iron, a reel of thin fluxed core solder. Practice on some bits of copper wire. Clean till bright apply solder to each piece [tin] hold together NOT with hands apply solder till it flows do not move joint till it sets. When doing printed cct boards. a HOT iron for a short time is the way, else you may lift the copper.
Hope some of you take the time to learn. |
It`s not so much the soldering as knowing where to solder, think you need a sucker too to remove the old dry solder, way beyond my abilities |
|
Back to top |
|
|
jimmyw LifeTime Member
Age: 32 Zodiac: Joined: 30 Dec 2009 Posts: 1954 Location: Cork - Ireland
|
Posted: Mon Jun 16, 2014 0:54 Post subject: |
|
|
On mine I think the problem was there is some coiled enamel wire,the width of a hair,it crosses over,and rubs off itself,and after about 15 years of it the enamel coating wears off,bend them gently out of the way and it should do the trick.
I reflowed all the joints in mine too,you don't need a solder sucker to do it,but if you have one,you may as well do the whole lot again yourself get some of the older solder with the lead in it,it is far easier to work with,especially to learn on. To do it the easy way,just apply heat with the iron to all the joints one at a time,until it melts,let it flow into a cone shape and take the iron away and let it set. I'd guess you'd get away with maybe a 15 or 18 watt iron for it,especially with leaded solder,so it would be a cheap enough thing to buy if you were going to buy the gear. For learning it is the easiest to start with a tip that is cross cut rather than pointed,the cross cut one looks like a baguette cut diagonally,with a flat bit on the end. |
|
Back to top |
|
|
REVOGEL LifeTime Member
Age: 84 Zodiac: Joined: 23 Dec 2006 Posts: 4276 Location: Cent. Amelias. Reg 10. Guyana South America
|
Posted: Mon Jun 16, 2014 12:44 Post subject: |
|
|
agree with jimmyw 100%. Practice is the thing, why not raid the skips find some old toys with printed circuits in , and practice on them. If the solder is bright that is right, dull is a null http://www.bing.com/images/search?q=imiges+of+good+and+bad+soldered+joints&id=55F33C8447ED54C9E0CC2AF5
Take a gander at the above link to get a better idea of what we are on about.
You will be AMAZED at your capabilities. and the sense of achievement when you first get it right |
|
Back to top |
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You cannot download files in this forum
|
|