|
The Mitsubishi Pajero Owners ClubŪ The Mitsubishi Pajero, Shogun, Montero, Challenger, Raider and EVO 4x4 Owner's Club
|
View previous topic :: View next topic |
Author |
Message |
Biggaz84 Newbie
Age: 39 Zodiac: Joined: 12 May 2018 Posts: 6 Location: NELSON, LANCASHIRE
|
Posted: Sun Nov 18, 2018 22:34 Post subject: Help!! Front suspension top and bottom Ball joint issues.... |
|
|
Evening all. I have revently replaced top and bottom ball joints on both sides plus trsck rod ends and drop links so i thought it would be all hunky dory. Its now knocking again, buy was fine for a few days. Upon inspection it seems like the ball joints wernt pulled all the way in, especially the bottom ball joint. Ive removed the split pin again and tried to tighten the castle nut some more but its tight and now the ball joint is just spinning arround. Am i missing something, do they need pressing in? I just assunemed it was tighten till.it was tight, job done. First job ive done thats made it worse than it was before. Thanks in advance. |
|
Back to top |
|
|
Google Sponsor
|
Posted: Sun Nov 18, 2018 22:34 Post subject: Google Ads keep the POCUK free to join! |
|
|
|
|
Back to top |
|
|
Biggaz84 Newbie
Age: 39 Zodiac: Joined: 12 May 2018 Posts: 6 Location: NELSON, LANCASHIRE
|
Posted: Sun Nov 18, 2018 22:37 Post subject: |
|
|
2001 3.2 did by the way 👍 |
|
Back to top |
|
|
trekker ********
Age: 83 Zodiac: Joined: 25 Jun 2012 Posts: 5202 Location: Zimbabwe
|
Posted: Mon Nov 19, 2018 17:19 Post subject: |
|
|
Sounds like the spindle is too small in diameter, so wrong ball joint for your model. |
|
Back to top |
|
|
peteinchad LifeTime Member
Joined: 07 Jan 2013 Posts: 15079 Location: UK
|
Posted: Mon Nov 19, 2018 20:07 Post subject: |
|
|
You could always try a thick spring washer under the castle nut - it will allow the nut to pull the taper in a bit further, assuming there is enough thread on the spindle.
Just make sure that you can get the split pin in afterwards though - don't rely on the spring washer to keep it secure. |
|
Back to top |
|
|
alienidea LifeTime Member
Age: 54 Zodiac: Joined: 17 Jul 2006 Posts: 331 Location: llanelli
|
Posted: Tue Nov 20, 2018 23:32 Post subject: |
|
|
This happened to me with a rear top balljoint ..i used 2 thick washers to press it refitted the caster with plenty of thread on the spindle it did the trick |
|
Back to top |
|
|
SRJ *
Age: 37 Zodiac: Joined: 24 Oct 2018 Posts: 10 Location: Glasgow
|
Posted: Wed Nov 21, 2018 1:05 Post subject: |
|
|
Are you sure the nuts fully tight? Sounds like the balljoint is spinning inside inside the casing rathen than pulling the taper in tight.
Maybe worth lifting under the balljoint with a jack and tighten it again just incase. |
|
Back to top |
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You cannot download files in this forum
|
|